wyze doorbell v2 HL_DB2 boot log

gistfile1.txt

U-Boot SPL 2013.07 (Mar 07 2023 - 15:38:04)
Timer init
CLK stop
PLL init
pll_init:366
pll_cfg.pdiv = 10, pll_cfg.h2div = 5, pll_cfg.h0div = 5, pll_cfg.cdiv = 1, pll_cfg.l2div = 2
nf=116 nr = 1 od0 = 1 od1 = 2
cppcr is 07405100
CPM_CPAPCR 0740510d
nf=100 nr = 1 od0 = 1 od1 = 2
cppcr is 06405100
CPM_CPMPCR 0640510d
nf=100 nr = 1 od0 = 1 od1 = 2
cppcr is 06405100
CPM_CPVPCR 0640510d
cppcr 0x9a7b5510
apll_freq 1392000000 
mpll_freq 1200000000 
vpll_freq = 1200000000
ddr sel mpll, cpu sel apll
ddrfreq 600000000
cclk  1392000000
l2clk 696000000
h0clk 240000000
h2clk 240000000
pclk  120000000
CLK init
SDRAM init
sdram init start
ddr_inno_phy_init ..!
phy reg = 0x00000007, CL = 0x00000007
ddr_inno_phy_init ..! 11:  00000004
ddr_inno_phy_init ..! 22:  00000006
ddr_inno_phy_init ..! 33:  00000006
REG_DDR_LMR: 00000210
REG_DDR_LMR: 00000310
REG_DDR_LMR: 00000110
REG_DDR_LMR, MR0: 00f73011
T31_0x5: 00000007
T31_0x15: 0000000c
T31_0x4: 00000000
T31_0x14: 00000002
INNO_TRAINING_CTRL 1: 00000000
INNO_TRAINING_CTRL 2: 000000a1
T31_cc: 00000003
INNO_TRAINING_CTRL 3: 000000a0
T31_118: 0000003c
T31_158: 0000003c
T31_190: 0000001e
T31_194: 0000001d
jz-04 :  0x00000051 
jz-08 :  0x000000a0 
jz-28 :  0x00000024 
DDR PHY init OK
INNO_DQ_WIDTH   :00000003
INNO_PLL_FBDIV  :00000014
INNO_PLL_PDIV   :00000005
INNO_MEM_CFG    :00000051
INNO_PLL_CTRL   :00000018
INNO_CHANNEL_EN :0000000d
INNO_CWL        :00000006
INNO_CL         :00000007
DDR Controller init
DDRC_STATUS         0x80000001
DDRC_CFG            0x0aa88a42
DDRC_CTRL           0x0000011c
DDRC_LMR            0x00400008
DDRC_DLP            0x00000000
DDRC_TIMING1        0x050f0a06
DDRC_TIMING2        0x021c0a07
DDRC_TIMING3        0x200a0722
DDRC_TIMING4        0x26240031
DDRC_TIMING5        0xff060405
DDRC_TIMING6        0x321c0505
DDRC_REFCNT         0x00910503
DDRC_MMAP0          0x000020f8
DDRC_MMAP1          0x00002800
DDRC_REMAP1         0x030e0d0c
DDRC_REMAP2         0x07060504
DDRC_REMAP3         0x0b0a0908
DDRC_REMAP4         0x0f020100
DDRC_REMAP5         0x13121110
DDRC_AUTOSR_EN      0x00000000
sdram init finished
SDRAM init ok
board_init_r
image entry point: 0x80100000


U-Boot 2013.07 (Mar 07 2023 - 15:38:04)

Board: ISVP (Ingenic XBurst T31 SoC)
DRAM:  128 MiB
DTB: 0x8013de38
Top of RAM usable for U-Boot at: 84000000
Reserving 440k for U-Boot at: 83f90000
Reserving 32800k for malloc() at: 81f88000
Reserving 32 Bytes for Board Info at: 81f87fe0
Reserving 124 Bytes for Global Data at: 81f87f64
Reserving 128k for boot params() at: 81f67f64
Stack Pointer at: 81f67f48
Now running in RAM - U-Boot at: 83f90000
MMC:   msc: 0
Using default environment

In:    serial
Out:   serial
Err:   serial
gpio_request lable = wifi_enable_gpio gpio = 57
gpio_request lable = yellow_gpio gpio = 38
gpio_request lable = MACHINE_SW gpio = 59
gpio_request lable = blue_gpio gpio = 39
gpio_request lable = night_gpio gpio = 60
gpio_request lable = SPK_able_gpio gpio = 58
gpio_request lable = TF_en_gpio gpio = 47
gpio_request lable = TF_cd_gpio gpio = 48
gpio_request lable = SD_able_gpio gpio = 54
gpio_request lable = wifi_enable_gpio gpio = 57
gpio_request lable = sdupgrade gpio = 6
the manufacturer c8
SF: Detected GD25Q128

the manufacturer c8
SF: Detected GD25Q128

### JFFS2 loading 'upGradeFlag' to 0x82000000
Scanning JFFS2 FS: . done.
find_inode failed for name=upGradeFlag
load: Failed to find inode
### JFFS2 LOAD ERROR<0> for upGradeFlag!
Failed to read upGradeFlag file
gpio_request lable = TF_cd_gpio gpio = 48
the manufacturer c8
SF: Detected GD25Q128

--->probe spend 4 ms
SF: 2162688 bytes @ 0x50000 Read: OK
--->read spend 695 ms
## Loading kernel from FIT Image at 80600000 ...
   Using 'conf' configuration
   Verifying Hash Integrity ... sha256,rsa2048:kernel-dev+ sha256,rsa2048:kernel-dev+ OK
   Trying 'kernel' kernel subimage
     Description:  t31 kernel
     Type:         Kernel Image
     Compression:  uncompressed
     Data Start:   0x80600204
     Data Size:    1774234 Bytes = 1.7 MiB
     Architecture: MIPS
     OS:           Linux
     Load Address: 0x80f00000
     Entry Point:  0x80f00000
     Hash algo:    sha256
     Hash value:   2fbc2f8ff5abd1a3c5349aa294c64de23c9b7f6f8bf377da822c58ed6a1b454c
   Verifying Hash Integrity ... sha256+ OK
## Loading ramdisk from FIT Image at 80600000 ...
   Using 'conf' configuration
   Trying 'ramdisk' ramdisk subimage
     Description:  t31 ramdisk image
     Type:         RAMDisk Image
     Compression:  uncompressed
     Data Start:   0x807b15ac
     Data Size:    225381 Bytes = 220.1 KiB
     Architecture: MIPS
     OS:           Linux
     Load Address: 0x00000000
     Entry Point:  0x00000000
     Hash algo:    sha256
     Hash value:   6eeaed007afedcaa2edeeb57b4b194d7b146116614409620f23db849e8040cd0
   Verifying Hash Integrity ... sha256+ OK
## Loading fdt from FIT Image at 80600000 ...
   Using 'conf' configuration
   Trying 'fdt' fdt subimage
     Description:  t31 kernel dtb
     Type:         Flat Device Tree
     Compression:  uncompressed
     Data Start:   0x806000dc
     Data Size:    72 Bytes = 72 Bytes
     Architecture: MIPS
     Hash algo:    sha256
     Hash value:   4ee48e5ae650ede0b5a3548a1fd60e8aea0e71750ea43f8276ceafcd7cb091e0
   Verifying Hash Integrity ... sha256+ OK
   Loading fdt from 0x806000dc to 0x83000000
   Booting using the fdt blob at 0x83000000
   Loading Kernel Image ... OK
   Loading Ramdisk to 855c7000, end 855fe065 ... OK
   Loading Device Tree to 87ffc000, end 87fff047 ... OK

Starting kernel ...

[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 3.10.14__isvp_swan_1.0__ (xiao@xiao-virtual-machine) (gcc version 4.7.2 (Ingenic r2.3.3 2016.12) ) #1 PREEMPT Tue Apr 25 17:58:44 CST 2023
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 RESET ERROR PC:469E0339
[    0.000000] CPU0 revision is: 00d00100 (Ingenic Xburst)
[    0.000000] FPU revision is: 00b70000
[    0.000000] CCLK:1392MHz L2CLK:696Mhz H0CLK:200MHz H2CLK:200Mhz PCLK:100Mhz
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 004e5000 @ 00010000 (usable)
[    0.000000]  memory: 0003b000 @ 004f5000 (usable after init)
[    0.000000] User-defined physical RAM map:
[    0.000000]  memory: 05600000 @ 00000000 (usable)
[    0.000000] initrd addr is [0x855c7000] [0x855fe065], mapstart is [0x55ff]
[    0.000000] Initial ramdisk at: 0x855c7000 (225381 bytes)
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x055fffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x055fffff]
[    0.000000] Primary instruction cache 32kB, 8-way, VIPT, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 8-way, VIPT, no aliases, linesize 32 bytes
[    0.000000] pls check processor_id[0x00d00100],sc_jz not support!
[    0.000000] MIPS secondary cache 128kB, 8-way, linesize 32 bytes.
[    0.000000] Built 1 zonelists in Zone order, mobility grouping off.  Total pages: 21844
[    0.000000] Kernel command line: console=ttyS1,115200n8 mem=86M@0x0 rmem=42M@0x5600000 init=/linuxrc rootfstype=squashfs root=/dev/mtdblock2 rw mtdparts=jz_sfc:320K(boot),2112K(fit),6784K(rootfs),6784K(rback),320K(cfg),64K(oem)
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Memory: 80972k/88064k available (3697k kernel code, 7092k reserved, 1313k data, 236k init, 0k highmem)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] NR_IRQS:358
[    0.000000] clockevents_config_and_register success.
[    0.000015] Calibrating delay loop... 1391.00 BogoMIPS (lpj=6955008)
[    0.087830] pid_max: default: 32768 minimum: 301
[    0.092688] Mount-cache hash table entries: 512
[    0.097593] Initializing cgroup subsys debug
[    0.101849] Initializing cgroup subsys freezer
[    0.107202] devtmpfs: initialized
[    0.111960] regulator-dummy: no parameters
[    0.116321] NET: Registered protocol family 16
[    0.143461] bio: create slab <bio-0> at 0
[    0.153739] jz-dma jz-dma: JZ SoC DMA initialized
[    0.159976] SCSI subsystem initialized
[    0.164023] usbcore: registered new interface driver usbfs
[    0.170054] usbcore: registered new interface driver hub
[    0.175732] usbcore: registered new device driver usb
[    0.181359]  (null): set:249  hold:250 dev=100000000 h=500 l=500
[    0.187785] media: Linux media interface: v0.10
[    0.192473] Linux video capture interface: v2.00
[    0.199188] cfg80211: Calling CRDA to update world regulatory domain
[    0.206350] Switching to clocksource jz_clocksource
[    0.213594] NET: Registered protocol family 2
[    0.218542] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[    0.225709] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.232130] TCP: Hash tables configured (established 1024 bind 1024)
[    0.238565] TCP: reno registered
[    0.241841] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.247716] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.254268] NET: Registered protocol family 1
[    0.258750] Trying to unpack rootfs image as initramfs...
[    0.438352] Freeing initrd memory: 220K (855c7000 - 855fe000)
[    0.444689] freq_udelay_jiffys[0].max_num = 10
[    0.449114] cpufreq 	udelay 	loops_per_jiffy	
[    0.453614] 12000	 59956	 59956	
[    0.456798] 24000	 119913	 119913	
[    0.460242] 60000	 299784	 299784	
[    0.463777] 120000	 599569	 599569	
[    0.467228] 200000	 999282	 999282	
[    0.470758] 300000	 1498924	 1498924	
[    0.474495] 600000	 2997848	 2997848	
[    0.478176] 792000	 3957159	 3957159	
[    0.481904] 1008000	 5036385	 5036385	
[    0.485680] 1200000	 5995696	 5995696	
[    0.499645] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.505965] jffs2: version 2.2. © 2001-2006 Red Hat, Inc.
[    0.512115] msgmni has been set to 158
[    0.517665] alg: No test for stdrng (krng)
[    0.522204] io scheduler noop registered
[    0.526124] io scheduler cfq registered (default)
[    0.538294] jz-uart.1: ttyS1 at MMIO 0x10031000 (irq = 58) is a uart1
[    0.545937] console [ttyS1] enabled, bootconsole disabled
[    0.545937] console [ttyS1] enabled, bootconsole disabled
[    0.565745] brd: module loaded
[    0.573336] loop: module loaded
[    0.577709] zram: Created 2 device(s) ...
[    0.582486] logger: created 256K log 'log_main'
[    0.589113] jz TCU driver register completed
[    0.594959] the id code = c84018, the flash name is GD25Q127C
[    0.600887] JZ SFC Controller for SFC channel 0 driver register
[    0.607207] 6 cmdlinepart partitions found on MTD device jz_sfc
[    0.613407] Creating 6 MTD partitions on "jz_sfc":
[    0.618352] 0x000000000000-0x000000050000 : "boot"
[    0.624384] 0x000000050000-0x000000260000 : "fit"
[    0.630295] 0x000000260000-0x000000900000 : "rootfs"
[    0.636612] 0x000000900000-0x000000fa0000 : "rback"
[    0.642772] 0x000000fa0000-0x000000ff0000 : "cfg"
[    0.648683] 0x000000ff0000-0x000001000000 : "oem"
[    0.654780] SPI NOR MTD LOAD OK
[    0.658468] jz-dwc2 jz-dwc2: cgu clk gate get error
[    0.663686] DWC IN OTG MODE
[    0.667341] dwc2 dwc2: Keep PHY ON
[    0.670856] dwc2 dwc2: Using Buffer DMA mode
[    0.675412] dwc2 dwc2: Core Release: 3.00a
[    0.679676] dwc2 dwc2: DesignWare USB2.0 High-Speed Host Controller
[    0.686216] dwc2 dwc2: new USB bus registered, assigned bus number 1
[    0.693789] hub 1-0:1.0: USB hub found
[    0.697678] hub 1-0:1.0: 1 port detected
[    0.701930] dwc2 dwc2: DWC2 Host Initialized
[    0.706741] usbcore: registered new interface driver usb-storage
[    0.713401] usbcore: registered new interface driver usbserial
[    0.719606] usbcore: registered new interface driver pl2303
[    0.725559] usbserial: USB Serial support registered for pl2303
[    0.733188] device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) initialised: dm-devel@redhat.com
[    0.742298] jzmmc_v1.2 jzmmc_v1.2.0: vmmc regulator missing
[    0.748512] jzmmc_v1.2 jzmmc_v1.2.0: register success!
[    0.753975] jzmmc_v1.2 jzmmc_v1.2.1: vmmc regulator missing
[    0.759945] jzmmc_v1.2 jzmmc_v1.2.1: register success!
[    0.766159] usbcore: registered new interface driver usbhid
[    0.772011] usbhid: USB HID core driver
[    0.776136] TCP: cubic registered
[    0.779558] NET: Registered protocol family 17
[    0.784171] dwc2 dwc2: ID PIN CHANGED!
[    0.788120] lib80211: common routines for IEEE802.11 drivers
[    0.794982] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
^@[    0.803234] Freeing unused kernel memory: 236K (804f5000 - 80530000)
[    0.820891] verity [rootfs partition], fs type is [squashfs], verity mode is [0]
[    0.841137] bio: create slab <bio-1> at 1
[    0.845841] Verity success, dm device is [/dev/dm-0]
mdev is ok......
 __________________________________
|                                  |
|                                  |
|                                  |
|                                  |
| _   _             _           _  |
|| | | |_   _  __ _| |     __ _(_) |
|| |_| | | | |/ _| | |  _ / _| | | |
||  _  | |_| | (_| | |_| | (_| | | |
||_| |_|\__,_|\__,_|_____|\__,_|_| |
|                                  |
|                                  |
|_____2020_WYZE_VDB_V2_@HUALAI_____|


WCV3 login: [    1.620140] @@@@ tx-isp-probe ok(version H20211130a), compiler date=Nov 30 2021 @@@@@
[    1.663358] exFAT: Version 1.2.9
[    1.693842] jz_codec_register: probe() successful!
[    2.101534] dma dma0chan24: Channel 24 have been requested.(phy id 7,type 0x06 desc a2242000)
[    2.110635] dma dma0chan25: Channel 25 have been requested.(phy id 6,type 0x06 desc a2361000)
[    2.119815] dma dma0chan26: Channel 26 have been requested.(phy id 5,type 0x04 desc a2244000)
[    2.202363] jz_pwm_probe[228] d_name = tcu_chn0
[    2.208932] jz_pwm_probe[228] d_name = tcu_chn2
[    2.215547] jz_pwm_probe[228] d_name = tcu_chn3
[    2.222153] The version of PWM driver is H20180309a
[    2.233499] request pwm channel 0 successfully
[    2.238087] request pwm channel 2 successfully
[    2.244409] request pwm channel 3 successfully
[    2.249305] pwm-jz pwm-jz: jz_pwm_probe register ok !
[    2.269363] usbcore: registered new interface driver usb_ch34x
[    2.277209] ch34x: USB to serial driver for USB to serial chip ch340, ch341, etc.
[    2.284993] ch34x: V1.16 On 2020.12.23
################## to wait wifi vendor id ####################
[    2.372155] mmc1: new SDIO card at address 0001
################## [vendor:0x007a] atbm603x wifi ###################
[    2.662233] [atbm_log]:SVN_VER=20816,DPLL_CLOCK=24,BUILD_TIME=[===== =====]
[    2.669417] [atbm_log]:----drvier RATEPOLCIY=OLD
[    2.675888] [atbm_log]:Probe called
[    2.679544] [atbm_log]:atbm_sdio_probe:v12
[    2.683829] [atbm_log]:Allocated hw_priv @ 81156d80
[    2.689018] [atbm_log]:[BH] register.
[    2.692941] [atbm_log]:atbmwifi INIT_WORK enable
[    2.697756] [atbm_log]:atbmwifi INIT_WORK enable
[    2.702655] [atbm_log]:atbm_before_load_firmware++
[    2.707818] [atbm_log]:atbm_HwGetChipType, chipver=0x49, g_wifi_chip_type[10]
[    2.715217] [atbm_log]:atbm_sdio_rx_thread
[    2.719527] [atbm_log]:atbm_before_load_firmware:0xab0016c = [34800000]
[    2.726505] [atbm_log]:atbm_before_load_firmware:0xab0016c = [34800000]
[    2.733430] [atbm_log]:atbm_before_load_firmware:do not set config to smu
[    2.741236] [atbm_log]:rx timeout
[    2.745028] [atbm_log]:atbm_before_load_firmware:read [0x16100074]=[0],ret(0)
[    2.752457] [atbm_log]:atbm_before_load_firmware:write [0x16100074]=[1],ret(0)
[    2.760911] [atbm_log]:atbm_start_load_firmware++
[    2.765765] [atbm_log]:used firmware.h=
[    2.769711] [atbm_log]:START DOWNLOAD ICCM=========
[    2.774770] [atbm_log]:atbm_load_firmware_generic: addr 10000: len 22000
[    2.801907] [atbm_log]:START DOWNLOAD DCCM=========
[    2.806948] [atbm_log]:atbm_load_firmware_generic: addr 800000: len 9000
[    2.819408] [atbm_log]:atbm_after_load_firmware++
[    2.837747] [atbm_log]:firmwareCap f5ad
[    2.841726] [atbm_log]:firmwareCap2 51a4
[    2.845774] [atbm_log]:wsm_caps.firmwareCap 51a4f5ad
[    2.850721] [atbm_log]:apollo wifi WSM init done.
[    2.850721]    Input buffers: 42 x 1728 bytes
[    2.850721]    Hardware: 7.1280
[    2.850721]    WSM firmware [=MODEM=RF=Ares_AX  2GHZ Jun  6 2022 16:59:01NOTXConfrim], ver: 14449, build: 2835, api: 1060, cap: 0x51A4F5AD Config[30008]  expection 900b80c, ep0 cmd addr 901d3f8 NumOfStations[8] NumOfInterfaces[3]
[    2.884482] [atbm_log]:EFUSE(8)				[0]
[    2.888348] [atbm_log]:EFUSE(I)					[1]
[    2.892308] [atbm_log]:EFUSE(B)			[0]
[    2.896074] [atbm_log]:CAPABILITIES_ATBM_PRIVATE_IE      [0]
[    2.901920] [atbm_log]:CAPABILITIES_NVR_IPC              [1]
[    2.907762] [atbm_log]:CAPABILITIES_NO_CONFIRM           [1]
[    2.913606] [atbm_log]:CAPABILITIES_SDIO_PATCH           [0]
[    2.919446] [atbm_log]:CAPABILITIES_NO_BACKOFF           [1]
[    2.925294] [atbm_log]:CAPABILITIES_CFO                  [0]
[    2.931128] [atbm_log]:CAPABILITIES_AGC                  [1]
[    2.936977] [atbm_log]:CAPABILITIES_TXCAL                [1]
[    2.942815] [atbm_log]:CAPABILITIES_MONITOR              [0]
[    2.948649] [atbm_log]:CAPABILITIES_CUSTOM               [1]
[    2.954497] [atbm_log]:CAPABILITIES_SMARTCONFIG          [0]
[    2.960328] [atbm_log]:CAPABILITIES_ETF                  [1]
[    2.966174] [atbm_log]:CAPABILITIES_LMAC_RATECTL         [1]
[    2.972023] [atbm_log]:CAPABILITIES_LMAC_TPC             [1]
[    2.977854] [atbm_log]:CAPABILITIES_LMAC_TEMPC           [1]
[    2.983700] [atbm_log]:CAPABILITIES_CTS_BUG              [0]
[    2.989535] [atbm_log]:CAPABILITIES_USB_RECOVERY_BUG     [0]
[    2.995381] [atbm_log]:CAPABILITIES_USE_IPC              [0]
[    3.001229] [atbm_log]:CAPABILITIES_OUTER_PA             [0]
[    3.007069] [atbm_log]:CAPABILITIES_POWER_CONSUMPTION    [1]
[    3.012916] [atbm_log]:CAPABILITIES_RSSI_DECIDE_TXPOWER  [0]
[    3.018748] [atbm_log]:CAPABILITIES_RTS_LONG_DURATION    [1]
[    3.024596] [atbm_log]:CAPABILITIES_TX_CFO_PPM_CORRECTION[1]
[    3.030434] [atbm_log]:CAPABILITIES_SHARE_CRYSTAL       [0]
[    3.036191] [atbm_log]:CAPABILITIES_HW_CHECKSUM          [0]
[    3.042036] [atbm_log]:CAPABILITIES_SINGLE_CHANNEL_MULRX [0]
[    3.047872] [atbm_log]:CAPABILITIES_CFO_DCXO_CORRECTION  [1]
[    3.053720] [atbm_log]:EX_CAPABILITIES_TWO_CHIP_ONE_SOC	[0]
[    3.059284] [atbm_log]:EX_CAPABILITIES_MANUAL_SET_AC 	[0][atbm_log]:EX_CAPABILITIES_LMAC_BW_CONTROL	[1]
[    3.068981] [atbm_log]:EX_CAPABILITIES_SUPPORT_TWO_ANTENNA	[0][atbm_log]:EX_CAPABILITIES_ENABLE_STA_REMAIN_ON_CHANNEL	[1]
[    3.080296] [atbm_log]:EX_CAPABILITIES_ENABLE_PS 	   [1][atbm_log]:EX_CAPABILITIES_TX_REQUEST_FIFO_LINK 	   [0]
[    3.090708] [atbm_log]:EX_CAPABILITIES_CHIP_TYPE		6032IS
[    3.096367] [atbm_log]:CONFIG_PRODUCT_TEST_USE_FEATURE_ID [1]
[    3.102293] [atbm_log]:CONFIG_PRODUCT_TEST_USE_GOLDEN_LED [1]
[    3.115502] [atbm_log]:set_block_size=256
[    3.119635] [atbm_log]:mdelay wait wsm_startup_done  !!
[    3.125411] [atbm_log]:wsm_generic_confirm:status(2)
[    3.130580] [atbm_log]:<WARNING> wsm_write_mib fail !!! mibId=4132
[    3.137208] [atbm_log]:apollo wifi : can't open /data/.mac.info
[    3.143654] [atbm_log]:efuse data is [0x00]
[    3.153602] [atbm_log]:param:delta_gain1:-1 delta_gain2:-1 delta_gain3:-1 dcxo:-1
b_delta_gain1:10 b_delta_gain2:12 b_delta_gain3:15
gn_delta_gain1:10 gn_delta_gain2:8 gn_delta_gain3:12
[    3.170858] [atbm_log]:cmd: set_txpwr_and_dcxo,-1,-1,-1,-1,10,12,15,10,8,12 
[    3.178695] [atbm_log]:0,b_1M_2M=2
[    3.182227] [atbm_log]:1,b_5_5M_11M=2
[    3.186002] [atbm_log]:2,g_6M_n_6_5M=2
[    3.189866] [atbm_log]:3,g_9M=2
[    3.193114] [atbm_log]:4,g_12M_n_13M=2
[    3.196969] [atbm_log]:5,g_18M_n_19_5M=2
[    3.201005] [atbm_log]:6,g_24M_n_26M=2
[    3.204918] [atbm_log]:7,g_36M_n_39M=2
[    3.208782] [atbm_log]:8,g_48M_n_52M=2
[    3.212657] [atbm_log]:9,g_54M_n_58_5M=2
[    3.216697] [atbm_log]:10,n_65M=3
[    3.220427] [atbm_log]:get chip id [b4][1][1] 
[    3.225033] [atbm_log]:current chiptype 6032is 
[    3.230084] [atbm_log]:enable sg
[    3.243093] [atbm_log]:enable sg
[    3.255932] [atbm_log]:is registered as 'ALTOBEAM'
[    3.260878] [atbm_log]:[atbm_wtd]:set wtd_probe = 1
Updating device time to:
Tue Jul 11 01:15:56 UTC 2023
===========welcome to ver-comp tool=========
[ver-comp]dbg: appver:  4.51.0.5062
[ver-comp]dbg: rootver: 4.51.0.5062
[ver-comp]exec cmd: cp -rf /system/bin/app.ver /configs/
#######################
#   IS USER PROCESS   #
#######################
s:Bus 001 Device 001: ID 1d6b:0002

line_num:1
[FC] not found usb store
[FC] Test.tar no exist
[FC] In [user] mode!
kernel.core_pattern = |/system/bin/ucoredmp_collector.sh --pid %p --signal %s --name %e --time %t --output-dir /media/mmc/cores
kernel.core_pipe_limit = 1
net.unix.max_dgram_qlen = 128
[    6.652138] name : i2c0 nr : 0
[    6.741864]  sensor_read: addr=0x3107 value = 0xcc
[    6.831424] i2c i2c-0: i2c_jz_irq 441, I2C transfer error, ABORT interrupt
[    6.838531] i2c i2c-0: --I2C txabrt:
[    6.842300] i2c i2c-0: --I2C TXABRT[0]=I2C_TXABRT_ABRT_7B_ADDR_NOACK
[    6.848894] error: sensor_read,287 ret = -5
[    6.853232]  sensor_read: addr=0xf0 value = 0x0
[    6.857901] err sensor read addr = 0xf0, value = 0x0
[    6.951404] i2c i2c-0: i2c_jz_irq 441, I2C transfer error, ABORT interrupt
[    6.958501] i2c i2c-0: --I2C txabrt:
[    6.962243] i2c i2c-0: --I2C TXABRT[0]=I2C_TXABRT_ABRT_7B_ADDR_NOACK
[    6.968808] error: sensor_read,287 ret = -5
[    6.973136]  sensor_read: addr=0xa value = 0x0
[    6.977744] err sensor read addr = 0xa, value = 0x0
[    7.071408] i2c i2c-0: i2c_jz_irq 441, I2C transfer error, ABORT interrupt
[    7.078539] i2c i2c-0: --I2C txabrt:
[    7.082284] i2c i2c-0: --I2C TXABRT[0]=I2C_TXABRT_ABRT_7B_ADDR_NOACK
[    7.088868] error: sensor_read,287 ret = -5
[    7.093196]  sensor_read: addr=0x3f0 value = 0x0
[    7.097956] err sensor read addr = 0x3f0, value = 0x0
[    7.191398] i2c i2c-0: i2c_jz_irq 441, I2C transfer error, ABORT interrupt
[    7.198616] i2c i2c-0: --I2C txabrt:
[    7.202393] i2c i2c-0: --I2C TXABRT[0]=I2C_TXABRT_ABRT_7B_ADDR_NOACK
[    7.208986] error: sensor_read,287 ret = -5
[    7.213325]  sensor_read: addr=0xa value = 0x0
[    7.217911] err sensor read addr = 0xa, value = 0x0
[    7.311408] i2c i2c-0: i2c_jz_irq 441, I2C transfer error, ABORT interrupt
[    7.318508] i2c i2c-0: --I2C txabrt:
[    7.322250] i2c i2c-0: --I2C TXABRT[0]=I2C_TXABRT_ABRT_7B_ADDR_NOACK
[    7.328820] error: sensor_read,287 ret = -5
[    7.333140]  sensor_read: addr=0xa value = 0x0
[    7.337720] err sensor read addr = 0xa, value = 0x0
[    7.431837]  sensor_read: addr=0x3107 value = 0xcc
[    7.521857]  sensor_read: addr=0x3107 value = 0xcc
[    7.527397]  sensor_read: addr=0x3108 value = 0x40
[    7.532418] info: success sensor find : sc301IoT
[    7.537207] misc sinfo_release
[    7.672389] probe ok ------->sc301IoT
[    7.831913] -----sc301IoT_detect: 837 ret = 0, v = 0xcc
[    7.837909] -----sc301IoT_detect: 845 ret = 0, v = 0x40
[    7.843325] sc301IoT chip found @ 0x30 (i2c0)
[    7.847839] sensor driver version H20210818a
[    8.499814] sc301IoT stream on
[    9.001311] codec_set_device: set device: MIC...
[    9.331353] codec_set_device: set device: speaker...
[    9.344881] SPEAKER CTL MODE0 !
[    9.478181] [atbm_log]:[p2p0] change mac[xx]