Klipper printer config - Artillery Genius (MKS gen L)

printer.cfg

[include mainsail.cfg]

[gcode_macro _CLIENT_VARIABLE]
variable_use_custom_pos   : False ; use custom park coordinates for x,y [True/False]
variable_custom_park_x    : 0.0   ; custom x position; value must be within your defined min and max of X
variable_custom_park_y    : 0.0   ; custom y position; value must be within your defined min and max of Y
variable_custom_park_dz   : 2.0   ; custom dz value; the value in mm to lift the nozzle when move to park position
variable_retract          : 1.0   ; the value to retract while PAUSE
variable_cancel_retract   : 5.0   ; the value to retract while CANCEL_PRINT
variable_speed_retract    : 35.0  ; retract speed in mm/s
variable_unretract        : 1.0   ; the value to unretract while RESUME
variable_speed_unretract  : 35.0  ; unretract speed in mm/s
variable_speed_hop        : 15.0  ; z move speed in mm/s
variable_speed_move       : 100.0 ; move speed in mm/s
variable_park_at_cancel   : False ; allow to move the toolhead to park while execute CANCEL_PRINT [True/False]
variable_park_at_cancel_x : None  ; different park position during CANCEL_PRINT [None/Position as Float]; park_at_cancel must be True
variable_park_at_cancel_y : None  ; different park position during CANCEL_PRINT [None/Position as Float]; park_at_cancel must be True
# !!! Caution [firmware_retraction] must be defined in the printer.cfg if you set use_fw_retract: True !!!
variable_use_fw_retract  : False ; use fw_retraction instead of the manual version [True/False]
gcode:

[stepper_x]
step_pin: ar54
dir_pin: ar55
enable_pin: !ar38
microsteps: 16
rotation_distance: 39.80
endstop_pin: ^!ar3
position_endstop: 0
position_min: 0
position_max: 220
homing_speed: 40.0

[stepper_y]
step_pin: ar60
dir_pin: ar61
enable_pin: !ar56
microsteps: 16
rotation_distance: 39.88
endstop_pin: ^!ar14
position_endstop: 0
position_min: 0
position_max: 220
homing_speed: 40
homing_positive_dir: false

[stepper_z]
step_pin: ar46
dir_pin: !ar48
enable_pin: !ar62
microsteps: 16
rotation_distance: 8
endstop_pin: probe:z_virtual_endstop			   
position_min: -3
position_max: 250
homing_speed: 30
second_homing_speed: 1

[stepper_z1]
step_pin: ar36
dir_pin: !ar34
enable_pin: !ar30
microsteps: 16
rotation_distance: 8

[extruder]
step_pin: ar26
dir_pin: ar28
enable_pin: !ar24
microsteps: 16
rotation_distance: 7.49
nozzle_diameter: 0.400
filament_diameter: 1.750
heater_pin: ar10
sensor_type: EPCOS 100K B57560G104F
sensor_pin: analog13
min_extrude_temp: 180
min_temp: 5
max_temp: 300
max_extrude_only_distance: 500
max_extrude_cross_section: 2.0
pressure_advance: 0.070

[heater_bed]
heater_pin: ar8
sensor_type: EPCOS 100K B57560G104F
sensor_pin: analog14
min_temp: 5
max_temp: 150
smooth_time: 10
#control = pid
#pid_kp = 34.18
#pid_ki = 3.21
#pid_kd = 242.65

[fan]
pin: ar9
kick_start_time: 0.500

[heater_fan my_nozzle_fan]
pin:ar7
heater: extruder
heater_temp: 50.0
fan_speed: 1.0

[mcu]
#make sure this reflects your serial port you found when flashing klipper
#serial: /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0
serial: /dev/serial/by-path/platform-fd500000.pcie-pci-0000:01:00.0-usb-0:1.2:1.0-port0

[printer]
kinematics: cartesian
max_velocity: 200
max_accel: 3000
max_z_velocity: 50
max_z_accel: 100
square_corner_velocity: 5 

[bed_screws]
screw1: 45,45
screw1_name: front left
screw2: 185,45
screw2_name: front right
screw3: 185,185
screw3_name: back right
screw4: 45,185
screw4_name: back left
speed: 100.0

[bltouch]
sensor_pin: ar19 
control_pin: ar11 
x_offset:29
y_offset:-35
speed:10
samples:1
samples_result:average
set_output_mode: 5V
probe_with_touch_mode: true
stow_on_each_sample: false

[safe_z_home]
home_xy_position: 82,143
speed: 100
z_hop: 20               
z_hop_speed: 20

[bed_mesh]
speed: 800
mesh_min: 29,5
mesh_max: 215,185
probe_count: 8,8
mesh_pps: 2,2
algorithm: bicubic
bicubic_tension: 0.2
move_check_distance: 3.0
split_delta_z: .010
fade_start: 1.0 
fade_end: 5.0

[screws_tilt_adjust]
screw1: 17,78
screw1_name: front left
screw2: 157,78
screw2_name: front right
screw3: 17,218
screw3_name: back left
screw4: 157,218
screw4_name: back right
speed: 100.0
screw_thread: CW-M5			

[skew_correction]


#uncomment the following lines to use Z_TILT_ADJUST and uncomment G34 Macro to use G34
#[z_tilt]
#z_positions: 
#     10,155
#     270,155
#
#points: 
#    10,155
#    270,155
#speed: 100
#horizontal_move_z: 10

[gcode_macro G29]
gcode:
 BED_MESH_CLEAR
 G28
 BED_MESH_CALIBRATE
 BED_MESH_PROFILE SAVE=x1
 
#[gcode_macro G34]
#gcode:
#     G28
#     Z_TILT_ADJUST		

[gcode_macro G35]
gcode:
     G28
     SCREWS_TILT_CALCULATE
			 
[gcode_macro START_PRINT]			
gcode:
    {% set bed_temp = params.BED_TEMP|default(60)|float %}
    {% set extruder_temp = params.EXTRUDER_TEMP|default(210)|float %}
    #SET_GCODE_OFFSET Z=-0.080
    #SET_GCODE_OFFSET Z=+0.090
    #SET_GCODE_OFFSET Z=+0.010
    SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET={bed_temp}
    TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM={bed_temp - 1}
    # Home the printer
	G29 				 		  						 
    # Use absolute coordinates
    G90
    # Wait for hotend temp
    SET_HEATER_TEMPERATURE HEATER=extruder TARGET={extruder_temp}
    G1 X0 Y0 Z30 F3000
    TEMPERATURE_WAIT SENSOR=extruder MINIMUM={extruder_temp} MAXIMUM={extruder_temp + 2}
    # Move the nozzle near the bed
    G1 X0 Y0 Z5 F3000
    # Move the nozzle very close to the bed
    G1 Z0.15 F300
    G92 E0 ;Reset Extruder
    
    G1 X20 Y5 Z0.3 F5000.0			   
    G1 Z0.3 F1000 			    
    G1 X50 Y5 F1500.0 E5 			   
    G1 X50 Y5.3 Z0.3 F5000.0			    
    G1 X5.3  Y5.3 Z0.3 F1500.0 E10 			

    G21 ; set units to millimeters
    G90 ; use absolute coordinates
    M83 ; use relative distances for extrusion
    G92 E0
    SKEW_PROFILE LOAD=CaliFlower

[gcode_macro END_PRINT]
gcode:
    # Turn off bed, extruder, and fan
    M140 S0
    M104 S0
    M106 S0
    # Move nozzle away from print while retracting
    G91
    G1 Z20 X10 Y10 E-3 F3000
    G90
    G1 Y200 F6000
    # Disable steppers
    M84
    SET_SKEW CLEAR=1

[pause_resume]
recover_velocity: 50.

#[filament_switch_sensor my_sensor]
#Move filament runout sensor from TFT to X+ endstop pin. Umcomment all but this line if you want to use this
#pause_on_runout: False
#runout_gcode: PAUSE
#insert_gcode: RESUME
#switch_pin: ar2

# Arduino aliases for atmega2560/1280 (Arduino mega) boards
[board_pins arduino-mega]
aliases:
    ar0=PE0, ar1=PE1, ar2=PE4, ar3=PE5, ar4=PG5,
    ar5=PE3, ar6=PH3, ar7=PH4, ar8=PH5, ar9=PH6,
    ar10=PB4, ar11=PB5, ar12=PB6, ar13=PB7, ar14=PJ1,
    ar15=PJ0, ar16=PH1, ar17=PH0, ar18=PD3, ar19=PD2,
    ar20=PD1, ar21=PD0, ar22=PA0, ar23=PA1, ar24=PA2,
    ar25=PA3, ar26=PA4, ar27=PA5, ar28=PA6, ar29=PA7,
    ar30=PC7, ar31=PC6, ar32=PC5, ar33=PC4, ar34=PC3,
    ar35=PC2, ar36=PC1, ar37=PC0, ar38=PD7, ar39=PG2,
    ar40=PG1, ar41=PG0, ar42=PL7, ar43=PL6, ar44=PL5,
    ar45=PL4, ar46=PL3, ar47=PL2, ar48=PL1, ar49=PL0,
    ar50=PB3, ar51=PB2, ar52=PB1, ar53=PB0, ar54=PF0,
    ar55=PF1, ar56=PF2, ar57=PF3, ar58=PF4, ar59=PF5,
    ar60=PF6, ar61=PF7, ar62=PK0, ar63=PK1, ar64=PK2,
    ar65=PK3, ar66=PK4, ar67=PK5, ar68=PK6, ar69=PK7,
    analog0=PF0, analog1=PF1, analog2=PF2, analog3=PF3, analog4=PF4,
    analog5=PF5, analog6=PF6, analog7=PF7, analog8=PK0, analog9=PK1,
    analog10=PK2, analog11=PK3, analog12=PK4, analog13=PK5, analog14=PK6,
    analog15=PK7,
    # Marlin adds these additional aliases
    ml70=PG4, ml71=PG3, ml72=PJ2, ml73=PJ3, ml74=PJ7,
    ml75=PJ4, ml76=PJ5, ml77=PJ6, ml78=PE2, ml79=PE6,
    ml80=PE7, ml81=PD4, ml82=PD5, ml83=PD6, ml84=PH2,
    ml85=PH7

#*# <---------------------- SAVE_CONFIG ---------------------->
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
#*#
#*# [extruder]
#*# control = pid
#*# pid_kp = 21.758
#*# pid_ki = 1.099
#*# pid_kd = 107.700
#*#
#*# [bltouch]
#*# z_offset = 2.525
#*#
#*# [bed_mesh default]
#*# version = 1
#*# points =
#*# 	  -0.032500, -0.065000, -0.055000, -0.072500, -0.072500, -0.057500, -0.090000, -0.095000
#*# 	  0.057500, 0.017500, 0.022500, 0.007500, -0.007500, 0.005000, -0.020000, -0.025000
#*# 	  0.135000, 0.085000, 0.087500, 0.057500, 0.057500, 0.077500, 0.045000, 0.035000
#*# 	  0.102500, 0.050000, 0.055000, 0.025000, 0.027500, 0.047500, 0.020000, 0.017500
#*# 	  0.092500, 0.035000, 0.040000, 0.017500, 0.010000, 0.022500, -0.017500, -0.012500
#*# 	  0.082500, 0.035000, 0.040000, 0.027500, 0.020000, 0.045000, 0.017500, 0.027500
#*# 	  0.075000, 0.030000, 0.032500, 0.007500, -0.005000, 0.015000, -0.015000, -0.015000
#*# 	  0.085000, 0.045000, 0.042500, 0.015000, 0.000000, -0.002500, -0.025000, -0.035000
#*# x_count = 8
#*# y_count = 8
#*# mesh_x_pps = 2
#*# mesh_y_pps = 2
#*# algo = bicubic
#*# tension = 0.2
#*# min_x = 29.0
#*# max_x = 214.99
#*# min_y = 5.0
#*# max_y = 184.97
#*#
#*# [bed_mesh x1]
#*# version = 1
#*# points =
#*# 	  -0.032500, -0.065000, -0.055000, -0.072500, -0.072500, -0.057500, -0.090000, -0.095000
#*# 	  0.057500, 0.017500, 0.022500, 0.007500, -0.007500, 0.005000, -0.020000, -0.025000
#*# 	  0.135000, 0.085000, 0.087500, 0.057500, 0.057500, 0.077500, 0.045000, 0.035000
#*# 	  0.102500, 0.050000, 0.055000, 0.025000, 0.027500, 0.047500, 0.020000, 0.017500
#*# 	  0.092500, 0.035000, 0.040000, 0.017500, 0.010000, 0.022500, -0.017500, -0.012500
#*# 	  0.082500, 0.035000, 0.040000, 0.027500, 0.020000, 0.045000, 0.017500, 0.027500
#*# 	  0.075000, 0.030000, 0.032500, 0.007500, -0.005000, 0.015000, -0.015000, -0.015000
#*# 	  0.085000, 0.045000, 0.042500, 0.015000, 0.000000, -0.002500, -0.025000, -0.035000
#*# x_count = 8
#*# y_count = 8
#*# mesh_x_pps = 2
#*# mesh_y_pps = 2
#*# algo = bicubic
#*# tension = 0.2
#*# min_x = 29.0
#*# max_x = 214.99
#*# min_y = 5.0
#*# max_y = 184.97
#*#
#*# [heater_bed]
#*# control = pid
#*# pid_kp = 44.037
#*# pid_ki = 0.459
#*# pid_kd = 1056.877
#*#
#*# [skew_correction CaliFlower]
#*# xy_skew = -0.005421733961664335
#*# xz_skew = 0.0
#*# yz_skew = 0.0

Merci!

Hello, when I try to start printing, the header CRASHES hard over the heated bed and I must to stop inmediately!! Can you help me? I have 3D touch and ive done the probe and pin up and down and all goes well

I did this config a long time ago so my memories are quite bad about how to troubleshoot this kind of problem.
Seems like the z-probe is not well configured :/
My printer uses a BL-Touch, i'm not sure it's the same as your 3D Touch. Maybe have a look at the z-probe config, check your wiring.

Thanks for your comment. Ive changed the pins name using 3d touch Klipper configuration, and detects when doing Z-Probe... but curious is i have a Z of 23.510 and in this configuration I see just 2.51
I will check how to modify Z_probe as you say

Hello, checked the Z_offset and change to 2.51, and when I try to print, the hotend crashes over the hot bed...
Ive use Klipper for Artillery Genius from other repositories too... Genius stock, Genius BL, Genius Z-Stop and nothing... she wants always to crash the hot bed

and does the probes behave normally when tested separately ?

Yes. Tested pin up and pin down and works
Done G28 and touch over my finger first and over the hot bed after and works
In Cura used the "gcode" START_PRINT and starts well, but after touch the bed with the 3D touch, it goes up a while and after that it crashes over the bed very hard

Hello again.. one thing I didnt mentioned... I have a Bon Tech installed, and when I try to extrude filament, it goes inverse and retracts filament... can be this the problem? How can I reverse the direction of extruder? Thanks in advance

Hello, i think at this point the best thing would be to understand how the printer.cfg is working. Try following the klipper documentation from the start and build your own printer.cfg.

Thanks a lot