DS18B20 on BigTreeTech Pi

BTT_Pi_DS18B20.md

DS18B20 on BigTreeTech Pi v1.2

BTT Pi uses AllWinner H616 CPU, and on https://github.com/bigtreetech/CB1 system, w1-gpio kernel module does not work.

However, there is an excellent custom module https://github.com/pstolarz/w1-gpio-cl

The following steps were tested on CB1 v2.3.3.

Wiring

DS18B20 Pinout
BTT Pi GPIO

Connect sensor VCC pin to 3.3V, GND to GND (obviously), and signal pin to selected GPIO. I used PC7, since it corresponds to the default w1 pin location on the Raspberry Pi header.
Don't forget to add a pull-up resistor between 3.3V and the signal pin. A 4.7 kOhm resistor is the recommended value.

NEVER connect anything while the printer is powered on!

I did not try parasitic power mode, and I don't recommend it. Klipper will shut down on subsequent read errors, and it might ruin your prints randomly. I did not have any problems with the standard 3-wire connection yet.

Compilation on CB1 system

The easiest way is to compile it directly on the device. The official guide needed to be modified slightly.

1. sudo apt-get install build-essential bc bison flex libssl-dev
2. sudo apt-get install linux-headers-current-sun50iw9
3. git clone https://github.com/pstolarz/w1-gpio-cl.git
4. cd w1-gpio-cl
5. ln -s /lib/modules/`uname -r`/build/include/linux w1
6. make
7. sudo make install

DKMS

Optionally, you can install it using DKMS

sudo dkms add .
sudo dkms install w1-gpio-cl/1.2.2

where 1.2.1 is the latest w1-gpio-cl release version.

Installation

For details, read the original README.

Pin Selection

The w1-gpio-cl module does not accept pin names; instead, it needs pin index. To list all available pins, run

sudo cat /sys/kernel/debug/pinctrl/300b000.pinctrl/pinmux-pins

Find your preferred pin (note that some pins might not work). I used PC7

pin 71 (PC7): UNCLAIMED

Now you can configure module options

echo 'options w1-gpio-cl m1="gdt:71"' | sudo tee /etc/modprobe.d/w1-gpio-cl.conf

Test Config

Try loading the module manually

sudo modprobe w1-gpio-cl

Verify that the module is loaded

lsmod | grep w1

You should see something like

w1_therm               28672  0
w1_gpio_cl             16384  0

You can verify the output of the dmesg for errors.

Automatic Loading

To load the module during boot, run

echo 'w1-gpio-cl' | sudo tee /etc/modules-load.d/w1-gpio-cl.conf

Reboot and verify that the module is properly loaded and working.

Configuration

See https://www.klipper3d.org/Config_Reference.html#ds18b20-temperature-sensor

Find out connected sensor addresses

sudo ls /sys/bus/w1/devices/

You will see output like

28-011319f769fe  w1_bus_master1

With that address, add a Klipper config section like this

[temperature_sensor my_sensor]
sensor_type: DS18B20
serial_no: 28-011319f769fe
sensor_mcu: CB1

Note that sensor_mcu must be set to the host, which is CB1 by default.

After restarting Klipper, your new temperature sensor should appear in the Mainsail/Fluidd UI automatically.

BTT_Pi_GPIO.png

@mdvorak Good to know my module is still alive, working on platforms I even didn't think about while creating it... I've added small fix in the project's Makefile so there is no need to create link manually as described in the README. You may check it out.

@mdvorak
I have a V0 printer that uses BBT PI and TFT35 SPI.
I have install your fix for the ghost touches. It works really well untill I install the software to use the DS18B20 1 wire thermistor according your repo.
As soon as I have the thermistor working, the ghost touches comes back.
If I re-install your ghost touches fix, if works again, but I loose the DS18B20 thermistor.

The software I used to fix the ghost is : https://github.com/freakydude/cb1-os-build

Do you know what could cause that problem ?
Is there a way to fix it so both things are working together ?

Thank you so much for creating this guide. I would not have figured this out on my own.

Hello. I have followed your guide but not getting any ID's from the 2 sensors I have hooked up. I am running a CB1 EMMC so I don't know if that makes anything different or not. Here is my dmesg output

biqu@BTT-CB1:~$ sudo ls /sys/bus/w1/devices/
w1_bus_master1
biqu@BTT-CB1:~$ dmesg
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000040000000-0x000000007fffffff]
[    0.000000]   DMA32    empty
[    0.000000]   Normal   empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000040000000-0x000000004007ffff]
[    0.000000]   node   0: [mem 0x0000000040080000-0x000000007fffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000007fffffff]
[    0.000000] cma: Reserved 128 MiB at 0x0000000076c00000
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.1 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] psci: SMC Calling Convention v1.2
[    0.000000] percpu: Embedded 18 pages/cpu s36504 r8192 d29032 u73728
[    0.000000] pcpu-alloc: s36504 r8192 d29032 u73728 alloc=18*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[    0.000000] Detected VIPT I-cache on CPU0
[    0.000000] CPU features: detected: ARM erratum 845719
[    0.000000] Fallback order for Node 0: 0
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 258048
[    0.000000] Policy zone: DMA
[    0.000000] Kernel command line: root=UUID=e345f9fc-00c8-4132-8e8e-8afa1304e8ed rootwait rootfstype=ext4 bootsplash.bootfile=bootsplash.armbian console=ttyS0,115200 console=tty1 consoleblank=0 loglevel=7 ubootpart= usb-storage.quirks=   cgroup_enable=memory swapaccount=1
[    0.000000] Unknown kernel command line parameters "ubootpart= cgroup_enable=memory", will be passed to user space.
[    0.000000] printk: log_buf_len individual max cpu contribution: 4096 bytes
[    0.000000] printk: log_buf_len total cpu_extra contributions: 12288 bytes
[    0.000000] printk: log_buf_len min size: 16384 bytes
[    0.000000] printk: log_buf_len: 32768 bytes
[    0.000000] printk: early log buf free: 14064(85%)
[    0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[    0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 868288K/1048576K available (13376K kernel code, 866K rwdata, 4040K rodata, 2240K init, 279K bss, 49216K reserved, 131072K cma-reserved)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] rcu: Hierarchical RCU implementation.
[    0.000000] rcu:     RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
[    0.000000]  Tracing variant of Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[    0.000000] Root IRQ handler: gic_handle_irq
[    0.000000] GIC: Using split EOI/Deactivate mode
[    0.000000] random: get_random_bytes called from start_kernel+0x4c4/0x6a4 with crng_init=0
[    0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.000000] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.000570] Console: colour dummy device 120x45
[    0.000916] printk: console [tty1] enabled
[    0.001007] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
[    0.001034] pid_max: default: 32768 minimum: 301
[    0.001114] LSM: Security Framework initializing
[    0.001156] Yama: becoming mindful.
[    0.001246] AppArmor: AppArmor initialized
[    0.001299] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[    0.001322] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[    0.002890] rcu: Hierarchical SRCU implementation.
[    0.004064] smp: Bringing up secondary CPUs ...
[    0.004538] Detected VIPT I-cache on CPU1
[    0.004612] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[    0.005181] Detected VIPT I-cache on CPU2
[    0.005244] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
[    0.005757] Detected VIPT I-cache on CPU3
[    0.005814] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
[    0.005902] smp: Brought up 1 node, 4 CPUs
[    0.005984] SMP: Total of 4 processors activated.
[    0.005998] CPU features: detected: 32-bit EL0 Support
[    0.006012] CPU features: detected: CRC32 instructions
[    0.018947] CPU: All CPU(s) started at EL2
[    0.019014] alternatives: patching kernel code
[    0.020520] devtmpfs: initialized
[    0.027164] Registered cp15_barrier emulation handler
[    0.027212] Registered setend emulation handler
[    0.027404] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.027438] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[    0.031908] pinctrl core: initialized pinctrl subsystem
[    0.033154] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[    0.034676] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations
[    0.034862] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[    0.034992] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[    0.035110] audit: initializing netlink subsys (disabled)
[    0.035376] audit: type=2000 audit(0.032:1): state=initialized audit_enabled=0 res=1
[    0.035868] thermal_sys: Registered thermal governor 'fair_share'
[    0.035875] thermal_sys: Registered thermal governor 'bang_bang'
[    0.035893] thermal_sys: Registered thermal governor 'step_wise'
[    0.035906] thermal_sys: Registered thermal governor 'user_space'
[    0.036497] cpuidle: using governor menu
[    0.036745] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[    0.036855] ASID allocator initialised with 65536 entries
[    0.037004] Serial: AMBA PL011 UART driver
[    0.048446] platform 6510000.tcon-top: Fixing up cyclic dependency with 6000000.hdmi
[    0.049125] platform 6515000.lcd-controller: Fixing up cyclic dependency with 6510000.tcon-top
[    0.050254] platform connector: Fixing up cyclic dependency with 6000000.hdmi
[    0.058393] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
[    0.058437] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages
[    0.058453] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[    0.058468] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages
[    0.059058] cryptd: max_cpu_qlen set to 1000
[    0.124165] raid6: neonx8   gen()  1804 MB/s
[    0.192206] raid6: neonx8   xor()  1347 MB/s
[    0.260269] raid6: neonx4   gen()  1846 MB/s
[    0.328313] raid6: neonx4   xor()  1335 MB/s
[    0.396364] raid6: neonx2   gen()  1752 MB/s
[    0.464423] raid6: neonx2   xor()  1241 MB/s
[    0.532469] raid6: neonx1   gen()  1524 MB/s
[    0.600528] raid6: neonx1   xor()  1047 MB/s
[    0.668584] raid6: int64x8  gen()  1252 MB/s
[    0.736634] raid6: int64x8  xor()   657 MB/s
[    0.804697] raid6: int64x4  gen()  1394 MB/s
[    0.872749] raid6: int64x4  xor()   705 MB/s
[    0.940801] raid6: int64x2  gen()  1189 MB/s
[    1.008865] raid6: int64x2  xor()   613 MB/s
[    1.076931] raid6: int64x1  gen()   886 MB/s
[    1.144985] raid6: int64x1  xor()   470 MB/s
[    1.144999] raid6: using algorithm neonx4 gen() 1846 MB/s
[    1.145013] raid6: .... xor() 1335 MB/s, rmw enabled
[    1.145025] raid6: using neon recovery algorithm
[    1.147207] iommu: Default domain type: Translated
[    1.147250] iommu: DMA domain TLB invalidation policy: strict mode
[    1.147567] SCSI subsystem initialized
[    1.147759] usbcore: registered new interface driver usbfs
[    1.147813] usbcore: registered new interface driver hub
[    1.147861] usbcore: registered new device driver usb
[    1.148329] pps_core: LinuxPPS API ver. 1 registered
[    1.148346] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <[email protected]>
[    1.148372] PTP clock support registered
[    1.148734] ARM FF-A: FFA_VERSION returned not supported
[    1.149242] Advanced Linux Sound Architecture Driver Initialized.
[    1.149907] NetLabel: Initializing
[    1.149934] NetLabel:  domain hash size = 128
[    1.149947] NetLabel:  protocols = UNLABELED CIPSOv4 CALIPSO
[    1.150023] NetLabel:  unlabeled traffic allowed by default
[    1.150265] mctp: management component transport protocol core
[    1.150282] NET: Registered PF_MCTP protocol family
[    1.150934] clocksource: Switched to clocksource arch_sys_counter
[    1.151150] VFS: Disk quotas dquot_6.6.0
[    1.151214] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    1.151777] AppArmor: AppArmor Filesystem Enabled
[    1.157558] NET: Registered PF_INET protocol family
[    1.157737] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear)
[    1.158553] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes, linear)
[    1.158600] TCP established hash table entries: 8192 (order: 4, 65536 bytes, linear)
[    1.158681] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear)
[    1.158812] TCP: Hash tables configured (established 8192 bind 8192)
[    1.158999] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[    1.159050] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[    1.159251] NET: Registered PF_UNIX/PF_LOCAL protocol family
[    1.159823] Trying to unpack rootfs image as initramfs...
[    1.172312] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available
[    1.173993] Initialise system trusted keyrings
[    1.174074] Key type blacklist registered
[    1.174341] workingset: timestamp_bits=44 max_order=18 bucket_order=0
[    1.179588] zbud: loaded
[    1.181123] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    1.183337] integrity: Platform Keyring initialized
[    1.226363] xor: automatically using best checksumming function   32regs
[    1.226410] async_tx: api initialized (async)
[    1.226428] Key type asymmetric registered
[    1.226442] Asymmetric key parser 'x509' registered
[    1.226650] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[    1.226950] io scheduler mq-deadline registered
[    1.226983] io scheduler kyber registered
[    1.227196] io scheduler bfq registered
[    1.238515] sun50i-h616-pinctrl 300b000.pinctrl: initialized sunXi PIO driver
[    1.239539] sun50i-h616-r-pinctrl 7022000.pinctrl: initialized sunXi PIO driver
[    1.247756] Serial: 8250/16550 driver, 6 ports, IRQ sharing disabled
[    1.249536] sun50i-h616-pinctrl 300b000.pinctrl: supply vcc-ph not found, using dummy regulator
[    1.250181] printk: console [ttyS0] disabled
[    1.250302] 5000000.serial: ttyS0 at MMIO 0x5000000 (irq = 32, base_baud = 1500000) is a 16550A
[    1.606071] Freeing initrd memory: 9036K
[    1.607535] printk: console [ttyS0] enabled
[    1.609419] misc dump reg init
[    2.276366] cacheinfo: Unable to detect cache hierarchy for CPU 0
[    2.286842] loop: module loaded
[    2.291352] mcp2515@0 enforce active low on chipselect handle
[    2.297215] sun50i-h616-pinctrl 300b000.pinctrl: supply vcc-pi not found, using dummy regulator
[    2.306074] st7789v@1 enforce active low on chipselect handle
[    2.311864] spidev@2 enforce active low on chipselect handle
[    2.318793] CAN device driver interface
[    2.323516] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    2.330076] ehci-platform: EHCI generic platform driver
[    2.335671] phy phy-5100400.phy.0: Changing dr_mode to 1
[    2.341019] ehci-platform 5101000.usb: EHCI Host Controller
[    2.346618] ehci-platform 5101000.usb: new USB bus registered, assigned bus number 1
[    2.354491] ehci-platform 5101000.usb: irq 37, io mem 0x05101000
[    2.374955] ehci-platform 5101000.usb: USB 2.0 started, EHCI 1.00
[    2.381344] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.16
[    2.389636] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.396869] usb usb1: Product: EHCI Host Controller
[    2.401757] usb usb1: Manufacturer: Linux 5.16.17-sun50iw9 ehci_hcd
[    2.408032] usb usb1: SerialNumber: 5101000.usb
[    2.413094] hub 1-0:1.0: USB hub found
[    2.416918] hub 1-0:1.0: 1 port detected
[    2.421502] ehci-platform 5200000.usb: EHCI Host Controller
[    2.427141] ehci-platform 5200000.usb: new USB bus registered, assigned bus number 2
[    2.435027] ehci-platform 5200000.usb: irq 39, io mem 0x05200000
[    2.454938] ehci-platform 5200000.usb: USB 2.0 started, EHCI 1.00
[    2.461305] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.16
[    2.469595] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.476827] usb usb2: Product: EHCI Host Controller
[    2.481715] usb usb2: Manufacturer: Linux 5.16.17-sun50iw9 ehci_hcd
[    2.487994] usb usb2: SerialNumber: 5200000.usb
[    2.493059] hub 2-0:1.0: USB hub found
[    2.496883] hub 2-0:1.0: 1 port detected
[    2.501461] ehci-platform 5310000.usb: EHCI Host Controller
[    2.507102] ehci-platform 5310000.usb: new USB bus registered, assigned bus number 3
[    2.514983] ehci-platform 5310000.usb: irq 41, io mem 0x05310000
[    2.534937] ehci-platform 5310000.usb: USB 2.0 started, EHCI 1.00
[    2.541329] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.16
[    2.549620] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.556853] usb usb3: Product: EHCI Host Controller
[    2.561741] usb usb3: Manufacturer: Linux 5.16.17-sun50iw9 ehci_hcd
[    2.568015] usb usb3: SerialNumber: 5310000.usb
[    2.573081] hub 3-0:1.0: USB hub found
[    2.576908] hub 3-0:1.0: 1 port detected
[    2.581499] ehci-platform 5311000.usb: EHCI Host Controller
[    2.587137] ehci-platform 5311000.usb: new USB bus registered, assigned bus number 4
[    2.595018] ehci-platform 5311000.usb: irq 43, io mem 0x05311000
[    2.614938] ehci-platform 5311000.usb: USB 2.0 started, EHCI 1.00
[    2.621294] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.16
[    2.629583] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.636815] usb usb4: Product: EHCI Host Controller
[    2.641703] usb usb4: Manufacturer: Linux 5.16.17-sun50iw9 ehci_hcd
[    2.647978] usb usb4: SerialNumber: 5311000.usb
[    2.653057] hub 4-0:1.0: USB hub found
[    2.656884] hub 4-0:1.0: 1 port detected
[    2.661309] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    2.667554] ohci-platform: OHCI generic platform driver
[    2.673200] ohci-platform 5101400.usb: Generic Platform OHCI controller
[    2.679867] ohci-platform 5101400.usb: new USB bus registered, assigned bus number 5
[    2.687743] ohci-platform 5101400.usb: irq 38, io mem 0x05101400
[    2.755156] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.16
[    2.763466] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.770699] usb usb5: Product: Generic Platform OHCI controller
[    2.776628] usb usb5: Manufacturer: Linux 5.16.17-sun50iw9 ohci_hcd
[    2.782903] usb usb5: SerialNumber: 5101400.usb
[    2.788016] hub 5-0:1.0: USB hub found
[    2.791845] hub 5-0:1.0: 1 port detected
[    2.796407] ohci-platform 5200400.usb: Generic Platform OHCI controller
[    2.803093] ohci-platform 5200400.usb: new USB bus registered, assigned bus number 6
[    2.810998] ohci-platform 5200400.usb: irq 40, io mem 0x05200400
[    2.818944] usb 1-1: new high-speed USB device number 2 using ehci-platform
[    2.879151] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.16
[    2.887441] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.894672] usb usb6: Product: Generic Platform OHCI controller
[    2.900590] usb usb6: Manufacturer: Linux 5.16.17-sun50iw9 ohci_hcd
[    2.906865] usb usb6: SerialNumber: 5200400.usb
[    2.911954] hub 6-0:1.0: USB hub found
[    2.915780] hub 6-0:1.0: 1 port detected
[    2.920339] ohci-platform 5310400.usb: Generic Platform OHCI controller
[    2.927029] ohci-platform 5310400.usb: new USB bus registered, assigned bus number 7
[    2.934930] ohci-platform 5310400.usb: irq 42, io mem 0x05310400
[    2.979542] usb 1-1: New USB device found, idVendor=1a40, idProduct=0101, bcdDevice= 1.11
[    2.987751] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[    2.994899] usb 1-1: Product: USB 2.0 Hub
[    2.999537] hub 1-1:1.0: USB hub found
[    3.003167] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.16
[    3.003417] hub 1-1:1.0: 4 ports detected
[    3.011597] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.022828] usb usb7: Product: Generic Platform OHCI controller
[    3.028768] usb usb7: Manufacturer: Linux 5.16.17-sun50iw9 ohci_hcd
[    3.035046] usb usb7: SerialNumber: 5310400.usb
[    3.040107] hub 7-0:1.0: USB hub found
[    3.043943] hub 7-0:1.0: 1 port detected
[    3.048499] ohci-platform 5311400.usb: Generic Platform OHCI controller
[    3.055187] ohci-platform 5311400.usb: new USB bus registered, assigned bus number 8
[    3.063075] ohci-platform 5311400.usb: irq 44, io mem 0x05311400
[    3.131161] usb usb8: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.16
[    3.139463] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.146698] usb usb8: Product: Generic Platform OHCI controller
[    3.152628] usb usb8: Manufacturer: Linux 5.16.17-sun50iw9 ohci_hcd
[    3.158904] usb usb8: SerialNumber: 5311400.usb
[    3.164005] hub 8-0:1.0: USB hub found
[    3.167830] hub 8-0:1.0: 1 port detected
[    3.172804] usbcore: registered new interface driver usb-storage
[    3.179353] usb_phy_generic usb_phy_generic.0.auto: supply vcc not found, using dummy regulator
[    3.189553] mousedev: PS/2 mouse device common for all mice
[    3.195381] usbcore: registered new interface driver usbtouchscreen
[    3.202717] sun6i-rtc 7000000.rtc: registered as rtc0
[    3.207923] sun6i-rtc 7000000.rtc: RTC enabled
[    3.212519] i2c_dev: i2c /dev entries driver
[    3.216821] Driver for 1-wire Dallas network protocol.
[    3.222942] sunxi-wdt 30090a0.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0)
[    3.232377] sun50i-h616-pinctrl 300b000.pinctrl: supply vcc-pg not found, using dummy regulator
[    3.241601] sdhci: Secure Digital Host Controller Interface driver
[    3.247819] sdhci: Copyright(c) Pierre Ossman
[    3.252221] Synopsys Designware Multimedia Card Interface Driver
[    3.259054] sdhci-pltfm: SDHCI platform and OF driver helper
[    3.259890] sunxi-mmc 4021000.mmc: allocated mmc-pwrseq
[    3.265067] sun50i-h616-pinctrl 300b000.pinctrl: supply vcc-pf not found, using dummy regulator
[    3.279768] ledtrig-cpu: registered to indicate activity on CPUs
[    3.286325] SMCCC: SOC_ID: ID = jep106:091e:1823 Revision = 0x00000000
[    3.292943] hid: raw HID events driver (C) Jiri Kosina
[    3.298234] usbcore: registered new interface driver usbhid
[    3.303819] usbhid: USB HID core driver
[    3.307665] SPI driver fb_st7796 has no spi_device_id for sitronix,st7796
[    3.330320] sunxi-hdmi soc:hdmi-audio@1: snd_soc_register_card failed
[    3.337565] NET: Registered PF_INET6 protocol family
[    3.378172] Segment Routing with IPv6
[    3.381943] In-situ OAM (IOAM) with IPv6
[    3.385973] NET: Registered PF_PACKET protocol family
[    3.391062] can: controller area network core
[    3.395510] NET: Registered PF_CAN protocol family
[    3.400482] 8021q: 802.1Q VLAN Support v1.8
[    3.404841] 9pnet: Installing 9P2000 support
[    3.409192] Key type dns_resolver registered
[    3.413924] registered taskstats version 1
[    3.418065] Loading compiled-in X.509 certificates
[    3.426508] Loaded X.509 cert 'Build time autogenerated kernel key: 238e852b21ade750ccb489d783c20372a97937da'
[    3.436609] usb 1-1.2: new full-speed USB device number 3 using ehci-platform
[    3.438762] zswap: loaded using pool zstd/z3fold
[    3.449190] Key type ._fscrypt registered
[    3.453275] Key type .fscrypt registered
[    3.457213] Key type fscrypt-provisioning registered
[    3.463207] Btrfs loaded, crc32c=crc32c-generic, zoned=yes, fsverity=no
[    3.470217] Key type encrypted registered
[    3.474282] AppArmor: AppArmor sha1 policy hashing enabled
[    3.479808] evm: Initialising EVM extended attributes:
[    3.484953] evm: security.selinux (disabled)
[    3.489233] evm: security.SMACK64
[    3.492554] evm: security.SMACK64EXEC
[    3.496225] evm: security.SMACK64TRANSMUTE
[    3.499504] sunxi-mmc 4021000.mmc: initialized, max. request size: 16384 KB, uses new timings mode
[    3.500326] evm: security.SMACK64MMAP
[    3.512946] evm: security.apparmor
[    3.515414] sunxi-mmc 4021000.mmc: card claims to support voltages below defined range
[    3.516356] evm: security.ima (disabled)
[    3.528195] evm: security.capability
[    3.531777] evm: HMAC attrs: 0x1
[    3.534876] mmc0: new high speed SDIO card at address 0001
[    3.550784] platform 1100000.mixer: Fixing up cyclic dependency with 6510000.tcon-top
[    3.562442] sunxi-hdmi soc:hdmi-audio@1: snd_soc_register_card failed
[    3.570389] sunxi-hdmi soc:hdmi-audio@1: snd_soc_register_card failed
[    3.577641] of_cfs_init
[    3.580255] of_cfs_init: OK
[    3.583439] ALSA device list:
[    3.586415]   #0: sndahub
[    3.589976] Freeing unused kernel memory: 2240K
[    3.603010] Run /init as init process
[    3.606681]   with arguments:
[    3.606688]     /init
[    3.606692]   with environment:
[    3.606697]     HOME=/
[    3.606701]     TERM=linux
[    3.606705]     ubootpart=
[    3.606710]     cgroup_enable=memory
[    3.681303] usb 1-1.2: New USB device found, idVendor=04d9, idProduct=8030, bcdDevice= 1.00
[    3.689784] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    3.697166] usb 1-1.2: Product: BTT-HDMI7
[    3.701236] usb 1-1.2: Manufacturer: BIQU
[    3.705290] usb 1-1.2: SerialNumber: SN0000000003
[    3.715369] input: BIQU BTT-HDMI7 as /devices/platform/soc/5101000.usb/usb1/1-1/1-1.2/1-1.2:1.0/0003:04D9:8030.0001/input/input0
[    3.734572] hid-generic 0003:04D9:8030.0001: input,hidraw0: USB HID v1.10 Device [BIQU BTT-HDMI7] on usb-5101000.usb-1.2/input0
[    3.748585] sunxi-hdmi soc:hdmi-audio@1: snd_soc_register_card failed
[    3.954996] usb 1-1.4: new full-speed USB device number 4 using ehci-platform
[    4.018738] sun50i-h616-pinctrl 300b000.pinctrl: supply vcc-pa not found, using dummy regulator
[    4.029310] it's ac300, skip the ac200 init!
[    4.033714] ac200: probe of 0-0010 failed with error -22
[    4.039938] mv64xxx_i2c 7081400.i2c: can't get pinctrl, bus recovery not supported
[    4.040954] sunxi-hdmi soc:hdmi-audio@1: snd_soc_register_card failed
[    4.051908] axp20x-i2c 1-0036: AXP20x variant AXP1530 found
[    4.084932] random: fast init done
[    4.091678] axp1530-dcdc3: Bringing 1500000uV into 1220000-1220000uV
[    4.115716] axp20x-i2c 1-0036: AXP20X driver loaded
[    4.135397] sunxi-hdmi soc:hdmi-audio@1: snd_soc_register_card failed
[    4.142659] debugfs: Directory '1100000.mixer' with parent 'regmap' already present!
[    4.150579] debugfs: Directory '1100000.mixer' with parent 'regmap' already present!
[    4.174676] sun4i-drm display-engine: bound 1100000.mixer (ops 0xffff800008dd4f00)
[    4.182558] sun4i-drm display-engine: bound 6510000.tcon-top (ops 0xffff800008dd8b38)
[    4.190761] sun4i-drm display-engine: bound 6515000.lcd-controller (ops 0xffff800008dd4028)
[    4.193292] usb 1-1.4: New USB device found, idVendor=1d50, idProduct=606f, bcdDevice= 0.00
[    4.207558] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    4.214900] usb 1-1.4: Product: stm32h723xx
[    4.219099] usb 1-1.4: Manufacturer: Klipper
[    4.223382] usb 1-1.4: SerialNumber: 3A0036001051313236343430
[    4.231043] sun8i-dw-hdmi 6000000.hdmi: Detected HDMI TX controller v2.12a with HDCP (DWC HDMI 2.0 TX PHY)
[    4.241238] sun8i-dw-hdmi 6000000.hdmi: EVENT=plugin
[    4.241415] sun8i-dw-hdmi 6000000.hdmi: registered DesignWare HDMI I2C bus driver
[    4.254636] sun4i-drm display-engine: bound 6000000.hdmi (ops 0xffff800008dd47d0)
[    4.262789] [drm] Initialized sun4i-drm 1.0.0 20150629 for display-engine on minor 0
[    4.270649] sun8i-dw-hdmi 6000000.hdmi: read_hpd result: 1
[    4.394321] bootsplash: Loading splash file (639808 bytes)
[    4.394423] bootsplash: Loaded (639808 bytes, 2 pics, 76 blobs).
[    4.463053] Console: switching to colour frame buffer device 128x37
[    4.498305] sun4i-drm display-engine: [drm] fb0: sun4i-drmdrmfb frame buffer device
[    4.519887] gmac-power0: NULL
[    4.523129] gmac-power1: NULL
[    4.526289] gmac-power2: NULL
[    5.349200] sun50i-h616-pinctrl 300b000.pinctrl: supply vcc-pc not found, using dummy regulator
[    5.386963] sunxi-mmc 4020000.mmc: initialized, max. request size: 16384 KB, uses new timings mode
[    5.387514] sunxi-mmc 4022000.mmc: initialized, max. request size: 2048 KB, uses new timings mode
[    5.515144] mmc2: new DDR MMC card at address 0001
[    5.521660] mmcblk2: mmc2:0001 BJTD4R 29.1 GiB
[    5.529225]  mmcblk2: p1 p2
[    5.535617] mmcblk2boot0: mmc2:0001 BJTD4R 4.00 MiB
[    5.542133] mmcblk2boot1: mmc2:0001 BJTD4R 4.00 MiB
[    6.592576] EXT4-fs (mmcblk2p2): mounted filesystem with writeback data mode. Opts: (null). Quota mode: none.
[    6.932690] systemd[1]: System time before build time, advancing clock.
[    6.963836] systemd[1]: systemd 247.3-7+deb11u4 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified)
[    6.987907] systemd[1]: Detected architecture arm64.
[    7.000560] systemd[1]: Set hostname to <BTT-CB1>.
[    7.498755] systemd[1]: /lib/systemd/system/hdmi-audio.service:10: Support for option SysVStartPriority= has been removed and it is ignored
[    7.556222] systemd[1]: Queued start job for default target Graphical Interface.
[    7.565175] random: systemd: uninitialized urandom read (16 bytes read)
[    7.574637] systemd[1]: Created slice system-getty.slice.
[    7.597887] random: systemd: uninitialized urandom read (16 bytes read)
[    7.607191] systemd[1]: Created slice system-modprobe.slice.
[    7.614368] random: systemd: uninitialized urandom read (16 bytes read)
[    7.624306] systemd[1]: Created slice system-serial\x2dgetty.slice.
[    7.649293] systemd[1]: Created slice system-systemd\x2dfsck.slice.
[    7.658828] systemd[1]: Created slice User and Session Slice.
[    7.665914] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[    7.675064] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[    7.699208] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[    7.710574] systemd[1]: Reached target Local Encrypted Volumes.
[    7.717470] systemd[1]: Reached target Paths.
[    7.722567] systemd[1]: Reached target Remote File Systems.
[    7.728806] systemd[1]: Reached target Slices.
[    7.733961] systemd[1]: Reached target Swap.
[    7.750987] systemd[1]: Listening on fsck to fsckd communication Socket.
[    7.759512] systemd[1]: Listening on initctl Compatibility Named Pipe.
[    7.768585] systemd[1]: Listening on Journal Audit Socket.
[    7.775832] systemd[1]: Listening on Journal Socket (/dev/log).
[    7.783461] systemd[1]: Listening on Journal Socket.
[    7.799119] systemd[1]: Listening on udev Control Socket.
[    7.806318] systemd[1]: Listening on udev Kernel Socket.
[    7.817757] systemd[1]: Mounting Huge Pages File System...
[    7.828924] systemd[1]: Mounting POSIX Message Queue File System...
[    7.840658] systemd[1]: Mounting Kernel Debug File System...
[    7.864927] systemd[1]: Condition check resulted in Kernel Trace File System being skipped.
[    7.879571] systemd[1]: Starting Restore / save the current clock...
[    7.891744] systemd[1]: Starting Create list of static device nodes for the current kernel...
[    7.905364] systemd[1]: Starting Load Kernel Module configfs...
[    7.924404] systemd[1]: Starting Load Kernel Module drm...
[    7.935532] systemd[1]: Starting Load Kernel Module fuse...
[    7.946062] systemd[1]: Started Nameserver information manager.
[    7.953800] systemd[1]: Reached target Network (Pre).
[    7.965426] fuse: init (API version 7.35)
[    7.966374] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped.
[    7.979279] systemd[1]: Condition check resulted in File System Check on Root Device being skipped.
[    7.995582] systemd[1]: Starting Journal Service...
[    8.007393] systemd[1]: Starting Load Kernel Modules...
[    8.018861] systemd[1]: Starting Remount Root and Kernel File Systems...
[    8.032274] systemd[1]: Starting Coldplug All udev Devices...
[    8.045259] w1_gpio_cl: loading out-of-tree module taints kernel.
[    8.050090] systemd[1]: Mounted Huge Pages File System.
[    8.051683] w1_gpio_cl: module verification failed: signature and/or required key missing - tainting kernel
[    8.066303] EXT4-fs (mmcblk2p2): re-mounted. Opts: commit=600,errors=remount-ro. Quota mode: none.
[    8.084474] systemd[1]: Mounted POSIX Message Queue File System.
[    8.091834] systemd[1]: Mounted Kernel Debug File System.
[    8.099882] systemd[1]: Finished Restore / save the current clock.
[    8.108801] systemd[1]: Finished Create list of static device nodes for the current kernel.
[    8.119738] systemd[1]: [email protected]: Succeeded.
[    8.127104] systemd[1]: Finished Load Kernel Module configfs.
[    8.139377] systemd[1]: [email protected]: Succeeded.
[    8.146145] systemd[1]: Finished Load Kernel Module drm.
[    8.153754] systemd[1]: [email protected]: Succeeded.
[    8.160648] systemd[1]: Finished Load Kernel Module fuse.
[    8.170080] systemd[1]: Finished Load Kernel Modules.
[    8.177602] systemd[1]: Finished Remount Root and Kernel File Systems.
[    8.205589] systemd[1]: Mounting FUSE Control File System...
[    8.216561] systemd[1]: Mounting Kernel Configuration File System...
[    8.225587] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped.
[    8.234701] systemd[1]: Condition check resulted in Platform Persistent Storage Archival being skipped.
[    8.249381] systemd[1]: Starting Load/Save Random Seed...
[    8.260709] systemd[1]: Starting Apply Kernel Variables...
[    8.272187] systemd[1]: Starting Create System Users...
[    8.283819] systemd[1]: Started Journal Service.
[    8.343194] systemd-journald[292]: Received client request to flush runtime journal.
[    8.350196] systemd-journald[292]: File /var/log/journal/bc065df264144c928a32b3c270f905df/system.journal corrupted or uncleanly shut down, renaming and replacing.
[    8.718444] panfrost 1800000.gpu: clock rate = 432000000
[    8.718489] panfrost 1800000.gpu: bus_clock rate = 200000000
[    8.731517] panfrost 1800000.gpu: mali-g31 id 0x7093 major 0x0 minor 0x0 status 0x0
[    8.731550] panfrost 1800000.gpu: features: 00000000,3fde77ff, issues: 00000000,00000400
[    8.731558] panfrost 1800000.gpu: Features: L2:0x07100206 Shader:0x00000000 Tiler:0x00000209 Mem:0x1 MMU:0x00002821 AS:0xff JS:0x7
[    8.731567] panfrost 1800000.gpu: shader_present=0x1 l2_present=0x1
[    8.745740] [drm] Initialized panfrost 1.2.0 20180908 for 1800000.gpu on minor 1
[    8.781594] debugfs: Directory '5096000.codec' with parent 'H616 Audio Codec' already present!
[    8.823308] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[    8.832672] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[    8.849510] cfg80211: loaded regulatory.db is malformed or signature is missing/invalid
[    8.915596] gs_usb 1-1.4:1.0: Configuring for 1 interfaces
[    8.916534] usbcore: registered new interface driver gs_usb
[    9.003569] input: BIQU BTT-HDMI7 as /devices/platform/soc/5101000.usb/usb1/1-1/1-1.2/1-1.2:1.0/0003:04D9:8030.0001/input/input1
[    9.004210] hid-multitouch 0003:04D9:8030.0001: input,hidraw0: USB HID v1.10 Device [BIQU BTT-HDMI7] on usb-5101000.usb-1.2/input0
[    9.193491] random: crng init done
[    9.193508] random: 7 urandom warning(s) missed due to ratelimiting
[    9.612779] zram: Added device: zram0
[    9.616524] zram: Added device: zram1
[    9.618146] zram: Added device: zram2
[    9.635498] IPv6: ADDRCONF(NETDEV_CHANGE): can0: link becomes ready
[    9.810390] zram0: detected capacity change from 0 to 1010640
[    9.906220] Adding 505316k swap on /dev/zram0.  Priority:5 extents:1 across:505316k SSFS
[   10.231462] zram1: detected capacity change from 0 to 102400
[   10.485566] systemd-journald[292]: File /var/log/journal/bc065df264144c928a32b3c270f905df/user-1000.journal corrupted or uncleanly shut down, renaming and replacing.
[   11.726190] mii_bus 5030000.ethernet-0 register success!
[   13.726579] sunxi-gmac 5030000.ethernet eth0: eth0: Type(7) PHY ID 00441400 at 0 IRQ poll (5030000.ethernet-0:00)
[   15.779271] sunxi-gmac 5030000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off
[   19.579211] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   22.351588] can: raw protocol

Hm, according to dmesg, module is loaded without error:

[    8.045259] w1_gpio_cl: loading out-of-tree module taints kernel.
[    8.051683] w1_gpio_cl: module verification failed: signature and/or required key missing - tainting kernel

Check again output of lsmod | grep w1 and then sudo ls /sys/bus/w1/devices/. If everything is OK but no devices are found, I would revisit wiring again. Also, try only one (or better, different) sensor. Cheap china clones are not always 100% functional.

sudo ls /sys/bus/w1/devices/

Here is the output I get from what you asked. Going to wire up a single sensor and give that a try. Im wondering if its because the CB1 EMMC has different GPIO numbers than the regular CB1 or BTT Pi

biqu@BTT-CB1:~$ lsmod | grep w1
w1_gpio_cl             16384  0
biqu@BTT-CB1:~$ sudo ls /sys/bus/w1/devices/
w1_bus_master1
biqu@BTT-CB1:~$

It does not seem like sw issue, so check the hw.

Just tried another single sensor. Same thing, not getting anything. Took that same sensor and hooked it up to a D1 Mini with ESP Home and I get an address from it and temp readings. Sensor is good. So its a SW issue.