Rafi's i3status configuration file

i3status.conf

# github.com/rafi i3status config

# i3status configuration file
# see "man i3status" for documentation.

# It is important that this file is edited as UTF-8.
# The following line should contain a sharp s:
# ß
# If the above line is not correctly displayed, fix your editor first!

general {
	colors = true
	color_good = "#BBBBBB"
	color_bad = "#CC1616"
	color_degraded = "#55858E"
	interval = 2
}

order += "volume master"
order += "load"
order += "cpu_usage"
order += "cpu_temperature 0"
order += "cpu_temperature 1"
order += "cpu_temperature 2"
order += "cpu_temperature 3"
order += "disk /"
order += "disk /media/media"
order += "ethernet eth0"
order += "tztime local"
#order += "ipv6"
#order += "run_watch DHCP"
#order += "run_watch VPN"
#order += "wireless wlan0"

volume master {
#	format = " ♪: %volume  " 
	device = "default"
	mixer = "Master"
	mixer_idx = 0
	# termsyn font
	format = "À %volume "
}

load {
#	format = " Δ: %1min "
	# termsyn font
	format = " Î %1min"
}

cpu_usage {
	format = "%usage "
}

cpu_temperature 0 {
	format = " ± %degrees°"
	path = "/sys/devices/platform/coretemp.0/temp2_input"
	max_threshold = 95
}

cpu_temperature 1 {
	format = "%degrees°"
	path = "/sys/devices/platform/coretemp.0/temp3_input"
	max_threshold = 95
}

cpu_temperature 2 {
	format = "%degrees°"
	path = "/sys/devices/platform/coretemp.0/temp4_input"
	max_threshold = 95
}

cpu_temperature 3 {
	format = "%degrees° "
	path = "/sys/devices/platform/coretemp.0/temp5_input"
	max_threshold = 95
}

disk "/" {
	format = " ¨ %avail:/ " 
}

disk "/media/media" {
	format = " ¨ %avail:m "
}

wireless wlan0 {
	format_up = " W: (%quality at %essid) %ip "
	format_down = " ☡ WiFi "
}

ethernet eth0 {
	# if you use %speed, i3status requires root privileges
#	format_up =  " Ω: %ip  "
#	format_down = " ∅ eth0  "

	# termsyn font
	format_up =  " ­ %ip "
	format_down = " Ð eth0 "
}

run_watch DHCP {
	pidfile = "/var/run/dhclient*.pid"
}

run_watch VPN {
	pidfile = "/var/run/vpnc/pid"
}

tztime local {
#	format = " %h-%d %H:%M ☰ "
	# termsyn font
	format = " %h-%d É %H:%M  ¸ ÈÈÈ È "
}

Thanks my friends !!!

How can I display the unicode symbols in my i3 status? They show up just fine in my editor, but when loading in i3 status the wrong symbol is displayed

Thanks guys, worked perfect here.

I love it <3 thanks!

How can I display the unicode symbols in my i3 status? They show up just fine in my editor, but when loading in i3 status the wrong symbol is displayed

Not sure but probably u need to use utf-8

Hi. To me the format displayed doesn't make much sense. For example, in my editor I see À in volume and ÈÈÈ È after time. And I see the same on the i3status. Is this how its supposed to be?
I pasted the output of i3status below.
À 66% | Î 0,88 | -4% | ± 54° | 58° | ¨ 307,0 GiB:/ | | Ð eth0 | mars-09 É 18:34 ¸ ÈÈÈ È | DHCP: yes | VPN: no | ☡ WiFi

Hi. To me the format displayed doesn't make much sense. For example, in my editor I see À in volume and ÈÈÈ È after time. And I see the same on the i3status. Is this how its supposed to be?
I pasted the output of i3status below.
À 66% | Î 0,88 | -4% | ± 54° | 58° | ¨ 307,0 GiB:/ | | Ð eth0 | mars-09 É 18:34 ¸ ÈÈÈ È | DHCP: yes | VPN: no | ☡ WiFi

did you find a solution?

No. I am using plain text now. Check it our here https://github.com/saki92/i3status/blob/main/config