-
-
Save patrickdk77/b687448fecff68d8572ac79a27d07862 to your computer and use it in GitHub Desktop.
| Template | |
| {"NAME":"Tuya Siren","GPIO":[255,107,255,108,255,255,0,0,255,255,255,255,255],"FLAG":0,"BASE":54} | |
| You must activate the template before using any of the tuya commands below. | |
| Recommended rules for tasmota: | |
| rule1 on system#boot backlog tuyasend4 102,0; tuyasend2 103,300; TuyaSend1 117,0 endon | |
| rule1 1 | |
| tuyamcu 11,104 | |
| This will set the default alarm length (5min), music (0), volume (0 high), and assign relay1 (power1) to the alarm activation. | |
| The alarm length and music doesn't appear to be retained during power cycles. | |
| 0x65 Power State 101 | |
| 55 aa 03 07 00 05 65 04 00 01 04 7c (on usb power) | |
| 55 aa 03 07 00 05 65 04 00 01 00 78 (on battery power, 0=full battery maybe (1/2/3 battery level?) | |
| x66 Change Alarm sound | |
| TuyaSend4 102,0 (0 to 11 on mine, other upto 17) | |
| x67 Change Alarm seconds | |
| TuyaSend2 103,10 (1 to 60 on mine, 1800 on another) | |
| x68 Alarm sounding | |
| TuyaSend4 104,0 (off) | |
| TuyaSend4 104,1 (on) | |
| 55 aa 03 07 00 05 68 01 00 01 01 79 | |
| 55 aa 03 07 00 05 71 01 00 01 00 81 | |
| x69 tempature reporting (105) | |
| 55 aa 03 07 00 08 69 02 00 04 00 00 00 c3 43 (tempature in C*10) | |
| x6a humidity reporting (106) | |
| 55 aa 03 07 00 08 6a 02 00 04 00 00 00 3b bc (59%) | |
| x6b temp alarm low in C | |
| TuyaSend4 107,17 | |
| 55 aa 00 06 00 08 6b 02 00 04 00 00 00 11 8f | |
| x6c temp alarm high in C | |
| TuyaSend4 108,38 | |
| 55 aa 00 06 00 08 6c 02 00 04 00 00 00 26 a5 | |
| x6d set humidity alarm low | |
| TuyaSend4 109,40 | |
| 55 aa 00 06 00 08 6d 02 00 04 00 00 00 46 c6 low in percent | |
| x6e set humidity alarm high | |
| TuyaSend4 110,80 | |
| 55 aa 00 06 00 08 6e 02 00 04 00 00 00 50 d1 high in percent | |
| x6f | |
| x70 Change to C and F units | |
| TuyaSend1 112,1 (on) | |
| 55 aa 00 06 00 05 70 01 00 01 01 7d (C) | |
| 55 aa 00 06 00 05 70 01 00 01 00 7c (F) | |
| x71 alarm temp on and off | |
| TuyaSend1 113,1 (on) | |
| 55 aa 00 06 00 05 71 01 00 01 01 7e (on) | |
| 55 aa 00 06 00 05 71 01 00 01 00 7d (off) | |
| x72 humidity alarm on/off | |
| TuyaSend1 114,1 (on) | |
| 55 aa 00 06 00 05 72 01 00 01 01 7f (on) | |
| 55 aa 00 06 00 05 72 01 00 01 00 7e (off) | |
| x73 alarm temp/humidity triggered | |
| 0=high tempature | |
| 1=high humidity | |
| 2=low tempature | |
| 3=low humidity | |
| 4=? | |
| 5=all normal | |
| 55 aa 03 07 00 05 73 04 00 01 02 88 (2 tempature alarm) | |
| 55 aa 03 07 00 05 73 04 00 01 03 89 (3 humidity alarm) | |
| 55 aa 03 07 00 05 73 04 00 01 05 8b (5 all clear) | |
| x74 Alarm db setting (loudness) | |
| TuyaSend1 117,0 (high) | |
| 55 aa 00 06 00 05 74 04 00 01 02 85 Low | |
| 55 aa 00 06 00 05 74 04 00 01 01 84 secondary | |
| 55 aa 00 06 00 05 74 04 00 01 00 83 High | |
hmmm spoke too soon, after cycling the power, no sound comes out of it, no matter what commands i send to it, even if i start from the rule1 setting and repeat what i did first time, changing power from off to on does nothing
Hi, did you fix it ?
I just flashed a MCU Product ID: {"p":"ymf4oruxqx0xlogp","v":"1.0.2","m":0} in 9.3.1 with no sound at all...Hi, I'm having the same issue. I got rhe same Product ID: {"p":"ymf4oruxqx0xlogp","v":"1.0.2","m":0} and flash it with tuya convert then firmware upgrade to tasmota 9.4.0. There is no sound emited after snding tuyasend command in the console I see the led flashing if TuyaSend4 104,1 enter in the console sending TuyaSend4 104,0 will turn off the flashing led but no sound. are there any solution on making this device work as expect. BTW. I having 2 of the same device and both of then having the same issue no sound.
I have it working without knowing what is the problem. the only thing I did after everything fails is configure mqtt setting on my device to connect to my mqtt server after it restart everything is working like magic. so I'm not sure that this is the real cause of all problem i have or not.
Yes !
You're right !!!
After setting up the MQTT broker, the TuyaSend commands are working.
Good news !
Hi @patrickdk77
I just got a NEDIS siren, and converted it, and tried out your template, it almost works!
This is great work, thanks!
My only problem is that it looses the selected alarm sound after a reboot.
I've changed the rule to:
rule1 on system#boot backlog tuyasend4 102,11; tuyasend2 103,300; TuyaSend1 117,0 endon
But it still uses alarm sound 0 (which is a doorbell).
I have no idea what you are doing, but it's great :-D
I wonder if it can be converted to ESPHome somehow...
It can be, just use the esphome tuya module.
I never published any more details on exactly how to set these up with exact instructions cause I killed two of them in the process of making this and didn't bother to buy a 3rd one. So I don't have a way currently to verify my instructions would work if I made them.
These things do not support rechargeable lithium batteries. using 4.2volts fries these things, so you have to stick to the 3.0v batteries.
I assume this is due to the voltage regulator cannot handle 8.4v, but only supports 6v.
Hey @patrickdk77
Tell me about it, burning items because you want to tinker :-D
When you write eg. "55 aa 03 07 00 05 68 01 00 01 01 79" is that the codes sent via the UART?
I have it working without knowing what is the problem. the only thing I did after everything fails is configure mqtt setting on my device to connect to my mqtt server after it restart everything is working like magic. so I'm not sure that this is the real cause of all problem i have or not.